Products

News

Learn more industry news

SF6 Cylinder Sizes and Purity Grades: What 8L, 40L, 99.5% and 99.995% Actually Buy You

The “8L” and “40L” on an SF6 cylinder are water capacity, not gas content. At the normal filling ratio of about 1.2–1.3 kg per litre of water capacity, an 8L cylinder holds roughly 10 kg of SF6 and a 40L holds roughly 50 kg. The purity figure is the other half of the specification, and the four grades we fill (99.5%, 99.9%, 99.95%, 99.995%) differ by a factor of 100 in total impurity: 5,000 ppm down to 50 ppm. Cylinder size decides what the gas costs you per kilogram. Purity decides whether the gas is allowed into the equipment at all.

Both numbers have to be right, and they are independent. A 40L of 99.5% and an 8L of 99.995% are not better or worse versions of each other. They are different products for different jobs.


What “8L” and “40L” actually measure

The litre figure stamped on the shoulder is the internal volume of the cylinder, measured with water. It says nothing about how much gas is inside. SF6 is stored as a liquid under its own vapour pressure, about 21 bar at 20 °C, so the useful quantity is the net fill weight in kilograms, not the volume.

Three consequences follow, and they cause most of the confusion we see in purchase orders.

The cylinder is not full of liquid. A cylinder is filled to a ratio, not to the brim. Industry practice sits around 1.2 to 1.3 kg of SF6 per litre of water capacity. That leaves ullage for thermal expansion, which matters because SF6 has a critical temperature of about 45.6 °C: above that there is no liquid phase at all, and a cylinder filled to the brim has nowhere for the liquid to go. A 40L at 1.25 kg/L gives 50 kg. An 8L at the same ratio gives 10 kg. Both figures are typical, neither is a legal maximum, and the number that binds you is the net weight on the packing list and the cylinder label.

Gross weight is not net weight. A 40L SF6 cylinder at 50 kg fill is a trolley job. If your site plans to carry cylinders up a stairwell or into a cramped GIS room, that is a handling decision you make before the PO, not after delivery.

You cannot read contents from pressure. While there is liquid in the cylinder, the pressure stays on the vapour pressure curve and barely moves as gas leaves. A gauge reading of 21 bar tells you the cylinder is not empty. It does not tell you whether it is 90% full or 15% full. Weigh it, or use a cylinder with a contents gauge.

One more practical point: SF6 is a liquefied gas, so the withdrawal rate matters. Pull gas too fast and you drag liquid droplets into the line, which is how people get a moisture spike in a compartment that was dry an hour ago. For filling GIS, use a proper gas cart with a vaporiser or a heated regulator rather than a bare regulator on the valve.


The four purity grades, translated into an impurity budget

Percentages hide the useful information. Convert them to parts per million and the grades separate cleanly:

Grade Total impurity budget What that budget has to cover
99.5% 5,000 ppm Air, nitrogen, CF₄, moisture, oil, acidic fluorides
99.9% 1,000 ppm Same list, five times tighter
99.95% 500 ppm Same list, ten times tighter than 99.5%
99.995% 50 ppm Same list, one hundred times tighter than 99.5%

That table is arithmetic, not marketing. The engineering question is what the budget gets spent on.

Moisture is the impurity that hurts most in electrical equipment. Water in SF₆ promotes acid formation and, over years, degrades insulation and attacks metal surfaces inside the compartment. Air and nitrogen dilute the dielectric strength, which is the whole reason SF₆ is in there. CF₄ is a process impurity from manufacture; it is relatively benign electrically but it counts against your purity and it is the first thing to look at when a lot tests low. Mineral oil comes from compressor lubricant and is a sign of a dirty filling line. Total acidity, reported as HF, tells you whether the gas has seen an arc or a bad pass through a desiccant.

A single purity number cannot separate these. Two lots can both read 99.9% and behave completely differently in a GIS, because one spent its 1,000 ppm on nitrogen and the other spent it on 180 ppm of water.

What the standards actually require

For new gas going into electrical equipment, the reference is IEC 60376:2018, Specification of technical grade sulphur hexafluoride (SF₆) and complementary gases for use in electrical equipment. The limits most often quoted from it are:

  • SF₆ content greater than 98.5% for pure gas (the standard’s floor, well below the 99.9% that buyers normally write into a PO)
  • Air below 10,000 ppmv
  • CF₄ below 4,000 ppmv
  • Water below 200 ppmv
  • Mineral oil below 10 ppmw
  • Total acidity below 7 ppmv

Check those numbers against the edition you are contracting to before you put them in a tender. The point is not the exact digit. The point is that the standard specifies six or seven parameters, and a supplier who quotes one is telling you what they measure.

Gas recovered from equipment and reused is a separate case, covered by IEC 60480:2019. Reconditioned gas is specified at 99.5% and it is a legitimate product, not a compromise, provided the lot was actually characterised after treatment. The failure mode is not “reconditioned”. It is reconditioned gas that nobody tested.


The 4 × 2 matrix: where each combination usually lands

Eight combinations, and in our experience they map onto eight fairly distinct buying patterns.

  8L (≈10 kg) 40L (≈50 kg)
99.5% Reconditioned-grade top-ups, training rigs, purge and leak-test practice, university demonstrations Reconditioned or top-up gas for a fleet of MV equipment where the recovery data is clean
99.9% Commissioning a single MV switchgear unit, one-off repairs, field service vans First fill on MV and 145 kV GIS production lines; the standard industrial workhorse
99.95% Laboratory dielectric test benches, R&D on gas mixtures, OEM acceptance testing HV GIS and GIL projects with a written moisture spec; breaker OEMs running type tests
99.995% Semiconductor and plasma process development, analytical method work, tracer studies, excimer-laser blend preparation Etch and chamber-clean supply for fabs; calibration gas blending; long-run research programmes

Two patterns are worth calling out.

The 8L cylinder is not a “sample size”. It is the correct package for anyone whose annual SF₆ consumption is under about 100 kg, because gas that sits in a cylinder for two years is working capital and shelf space, and because a 50 kg cylinder you only half use is a cylinder you eventually return with a heel you paid for. Field service is the clearest case: a technician needs enough gas for one compartment, not for a substation.

The 99.995% grade is usually bought by people who do not say “SF6″ at all. Semiconductor fabs buy it as an etch gas, analytical labs buy it as a high-purity background or blend component, and research groups buy it because a 50 ppm impurity floor keeps their baseline clean. Electrical buyers rarely need it. If your application is insulation, 99.9% or 99.95% with a tight moisture number will do the job that 99.995% would do, at a lower price, and the extra nines buy you nothing.


Cost per kilogram is not cost per usable kilogram

Two cylinders at the same purity and the same net weight can differ 20% in what they actually cost you to use. The gap comes from four places.

Fill weight. Underfilled cylinders are the oldest trick in the gas trade. A 40L that arrives with 46 kg instead of 50 kg costs you 8% on every refill for the life of the supply relationship. Weigh the first lot at your dock and compare against the packing list; do it again on a random lot each quarter.

Heel. You cannot evacuate a cylinder to zero with a regulator. Whatever is left when the pressure drops below your filling equipment’s requirement is gas you bought and cannot use. On an 8L the heel is a bigger share of the fill than on a 40L, which is one reason per-kg prices on small cylinders look worse than they are.

Purge and changeover losses. Each cylinder change on a filling line means purging the whip and the regulator. Fewer, larger cylinders mean fewer changeovers. This is a real cost on a production line and a rounding error in a lab.

Freight and dangerous goods handling. SF6 is UN 1079, class 2.2, with a toxic subsidiary risk. Sea freight moves under the IMDG Code, and each cylinder carries its own documentation weight. Per kilogram, small cylinders are more expensive to move. Per shipment, they are cheaper, which is why a first order or a single repair often goes out as 8L regardless of the unit rate.

If you want the arithmetic: take the quoted rate per kg, multiply by net fill, add freight and DG surcharges per cylinder, divide by the kilograms you will realistically draw out before the cylinder goes back. Do that for both sizes. The answer is frequently that 40L wins above 300 kg a year, 8L wins below 100 kg, and in between it depends on your storage.


How to choose, in order

  1. Start from the equipment spec, not the catalogue. The GIS or breaker nameplate states the SF₆ mass per compartment and the manufacturer states the required gas grade and moisture limit. Those two lines decide your purity. Everything else is packaging.
  2. Pick the grade that meets the spec with margin, and stop there. For most MV and HV insulation work that is 99.9% with moisture well inside the IEC 60376 limit. Move to 99.95% when the project writes a dew point into acceptance, or when the gas is going into a test bench where air content skews your measurements.
  3. Size the cylinder to your annual draw. Under 100 kg a year, 8L. Over 300 kg, 40L. In between, buy 40L for the production line and 8L for service.
  4. Ask for the per-lot certificate of analysis before you ask for the price. A CoA that names the lot and lists SF₆ content, air, moisture, CF₄, oil and acidity is worth more than a headline percentage. A certificate issued per shipment rather than per lot is a batch of unknowns with a stamp on it.
  5. Fix the valve and paperwork in writing. CGA 590 is the common SF₆ connection in North American plants, DIN on European lines. Chinese filling lines ship DIN-valved by default, so name who supplies the adapter. And check that the SDS section 14 and the dangerous goods declaration agree, character for character. That mismatch is what holds containers at port.

Questions we get on this one

How much does an 8L SF6 cylinder hold?

About 10 kg net at a 1.25 kg/L fill ratio. Treat it as typical, not guaranteed. The net weight on the cylinder label and the packing list is the binding figure, and it is the number you should be quoting in your cost calculations.

Is 99.9% pure enough for GIS?

For most medium-voltage and 145 kV gas-insulated switchgear, yes, provided the moisture and air results on the lot certificate are inside IEC 60376 limits. Plenty of buyers specify 99.99% or 99.995% as insurance. If the equipment manufacturer’s manual says 99.9%, the extra nines are cost without benefit.

What is the difference between 99.9% and 99.95% in practice?

500 ppm of impurity budget. In practice it shows up as tighter moisture and lower air content, which matters on test benches and on projects with a written dew point acceptance criterion. On a standard MV first fill, you will not measure the difference.

Can I use a 99.5% cylinder to top up a GIS?

Only if the compartment was filled with reconditioned-grade gas and your procedure allows it. 99.5% is the reconditioned grade under IEC 60480, not a new-gas grade. For a top-up on new equipment under warranty, use the grade the OEM specified.

Why is SF6 shipped as a liquid but sold by weight?

Because weight is the only measurement that does not move with temperature. Pressure tracks the vapour pressure curve until the liquid is gone, then falls away. Volume is fixed by the cylinder. Weight is what you are paying for.

Do I need a different cylinder for 99.995%?

The cylinder and valve are the same family. What changes is preparation: evacuation, passivation and a filling line clean enough not to add the impurities you just paid to remove. Ask for the lot moisture figure, not just the assay.

How should I store them?

Upright, valve cap on, below 45 °C, out of direct sun, away from heat sources, with the area ventilated. SF₆ is not flammable and not acutely toxic, but it is an asphyxiant: it displaces air in low-lying spaces, and in a basement storage room that is the actual hazard, not the gas chemistry.


Sources

  • IEC 60376:2018, Specification of technical grade sulphur hexafluoride (SF₆) and complementary gases for use in electrical equipment — webstore.iec.ch/en/publication/33028
  • IEC 60480:2019, Guidelines for the checking and treatment of sulphur hexafluoride (SF₆) taken from electrical equipment and specification for its re-use — webstore.iec.ch/en/publication/61024
  • Regulation (EU) 2024/573 on fluorinated greenhouse gases — eur-lex.europa.eu/eli/reg/2024/573/oj
  • ASTM D2472, Standard Specification for Sulfur Hexafluoride (electrical insulating gas, North American practice)
  • UN Model Regulations / IMDG Code, UN 1079, class 2.2 with toxic subsidiary risk

About the author

Newradar Gas (Hubei Newradar Electronic Gas Co., Ltd.) has been filling and exporting specialty gases since 2007, including SF₆ in 8L and 40L cylinders across the 99.5% to 99.995% range, with a per-lot certificate of analysis on export orders. If you are matching a cylinder size and grade to a specific switchgear or process spec, send us the nameplate line and the acceptance limits and we will tell you which combination fits. Product range: nrdgas.com/products.


Post time: Nov-16-2026